EMAX SKYLINE F3 flight controller Advanced Version

Features:

1. Practical - Easy to access connectors and solder pads.

2. Configurable - Choose to use connectors, solder pads or pins.

3. Stackable - Mount to your PDB or OSD.

4. Compact - Only 36x36mm.

5. Professional - Symmetrical, Neat and Tidy.

6. 8 Dedicated PWM outputs

7. 8 PWM Inputs

8. 36 I/O Connections

9. 72 MHz Clock Speed

10. 3 Hardware Serial Ports

11. 64Mb Flash Storage

12. The SkylineF3 gives you all the features you need for the heart of your aircraft, whether you\'re into FPV racing, acrobatic flying or aerial photography it\'s perfect.

Supports a variety of aircraft, tricopters, quad copters, hexacopters, helicopter, planes and more.

13. The SkylineF3 runs the open-source clean flight flight control (FC) software which has an ever-growing community of friendly developers and users. Being open-source means that you too can contribute to the system.

Flight Performance

 The SkylineF3 builds on tried and tested software, processor and sensor technology to make your aircraft fly like it\'s on rails.

No-Compromise I/O

 Use all the features all the time; e.g. connect your OSD SmartPort SBus GPS LED Strip Battery Monitoring Sonar 8 motors - all at the same time.

Configurable

 The SkylineF3 runs Cleanflight which can be configured to suit your needs using a cross-platform GUI (Windows/OSX/Linux).

Tiny and lightweight

The SkylineF3 has a standard 36x36mm form-factor with 30.5mm mounting holes and weighs just 6 grams.

Flight Logging

On-board high-capacity black box flight log recorder - optimize your tuning and see the results of your setup without guesswork.

Next-Generation CPU

The SkylineF3 has an ARM Cortex-M4 72Mhz CPU with Math co-processor (FPU) for efficient flight calculations that gets more done in less time. Loop times up to ~2x as fast as previous-generation STM32F1 based boards.

Developer Friendly

 Developer friendly debugging port (SWD) and boot mode selection, unbreakable boot loader.

One Shot ESC. Full support for OneShot ESCs for easy PID tuning and a sharper response.

Broad RC receiver Support

Supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers. No external inverters required (built-in).

Programmable LED

Dedicated output for programmable LEDs - great for orientation, racing and night flying.

Battery Monitoring

Battery monitoring ports for voltage and current.

Sonar

Sonar support for precision low-altitude hold.

I2C Port

I2C port always powered, perfect for external sensors or always-on OLED Screen.

Buzzer

Specifications:

The hardware was designed by the lead developer of clean flight to be more capable than the previous-generation STM32F1-based boards after hearing feedback from the clean flight users, contributors and top-pilots.

36x36mm board with 30.5mm mounting holes

Weight: 6 grams

Includes Compass and Barometer Sensors

STM32F303 CPU, 72Mhz inc FPU

High-Capacity Flash (Acro and Deluxe)

MPU6050 accelerometer/gyro

Micro USB socket

2x 8pin JST-SH sockets (PPM, PWM, SERIAL RX, GPIO, ADC, 3V, 5V, GND)

8x 3pin though-holes for pin headers for ESC/Servo connections

2x 4pin though-holes for pin headers for 2x serial ports

1x 2pin though-holes for pin headers for battery voltage

1x 2pin though-holes for pin headers for buzzer

1x 4pin JST-SH socket for I2C

1x 4pin JST-SH socket for SWD debugging