EMAX SKYLINE F3 flight controller Advanced Version
Features:
1. Practical - Easy to access connectors and solder pads.
2. Configurable - Choose to use connectors, solder pads or pins.
3. Stackable - Mount to your PDB or OSD.
4. Compact - Only 36x36mm.
5. Professional - Symmetrical, Neat and Tidy.
6. 8 Dedicated PWM outputs
7. 8 PWM Inputs
8. 36 I/O Connections
9. 72 MHz Clock Speed
10. 3 Hardware Serial Ports
11. 64Mb Flash Storage
12. The SkylineF3 gives you all the features you need for the heart of your aircraft, whether you\'re into FPV racing, acrobatic flying or aerial photography it\'s perfect.
Supports a variety of aircraft, tricopters, quad copters, hexacopters, helicopter, planes and more.
13. The SkylineF3 runs the open-source clean flight flight control (FC) software which has an ever-growing community of friendly developers and users. Being open-source means that you too can contribute to the system.
Flight Performance
The SkylineF3 builds on tried and tested software, processor and sensor technology to make your aircraft fly like it\'s on rails.
No-Compromise I/O
Use all the features all the time; e.g. connect your OSD SmartPort SBus GPS LED Strip Battery Monitoring Sonar 8 motors - all at the same time.
Configurable
The SkylineF3 runs Cleanflight which can be configured to suit your needs using a cross-platform GUI (Windows/OSX/Linux).
Tiny and lightweight
The SkylineF3 has a standard 36x36mm form-factor with 30.5mm mounting holes and weighs just 6 grams.
Flight Logging
On-board high-capacity black box flight log recorder - optimize your tuning and see the results of your setup without guesswork.
Next-Generation CPU
The SkylineF3 has an ARM Cortex-M4 72Mhz CPU with Math co-processor (FPU) for efficient flight calculations that gets more done in less time. Loop times up to ~2x as fast as previous-generation STM32F1 based boards.
Developer Friendly
Developer friendly debugging port (SWD) and boot mode selection, unbreakable boot loader.
One Shot ESC. Full support for OneShot ESCs for easy PID tuning and a sharper response.
Broad RC receiver Support
Supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers. No external inverters required (built-in).
Programmable LED
Dedicated output for programmable LEDs - great for orientation, racing and night flying.
Battery Monitoring
Battery monitoring ports for voltage and current.
Sonar
Sonar support for precision low-altitude hold.
I2C Port
I2C port always powered, perfect for external sensors or always-on OLED Screen.
Buzzer
Specifications:
The hardware was designed by the lead developer of clean flight to be more capable than the previous-generation STM32F1-based boards after hearing feedback from the clean flight users, contributors and top-pilots.
36x36mm board with 30.5mm mounting holes
Weight: 6 grams
Includes Compass and Barometer Sensors
STM32F303 CPU, 72Mhz inc FPU
High-Capacity Flash (Acro and Deluxe)
MPU6050 accelerometer/gyro
Micro USB socket
2x 8pin JST-SH sockets (PPM, PWM, SERIAL RX, GPIO, ADC, 3V, 5V, GND)
8x 3pin though-holes for pin headers for ESC/Servo connections
2x 4pin though-holes for pin headers for 2x serial ports
1x 2pin though-holes for pin headers for battery voltage
1x 2pin though-holes for pin headers for buzzer
1x 4pin JST-SH socket for I2C
1x 4pin JST-SH socket for SWD debugging