A4988 Stepper Motor Driver (2A)

55 EGP

Stepper motor driver Allegro’s A4988 DMOS Micro-stepping Driver with adjustable current limiting, overcurrent and overtemperature protection, and five different microstep resolutions (down to 1/16-step). The driver requires a logic supply voltage (3 – 5.5 V) and a motor supply voltage (8 – 35 )V. It can deliver up to approximately ... more on Future Electronics

Buy it from Future Electronics

Product Details

  • The best price of A4988 Stepper Motor Driver (2A) by Future Electronics in Egypt is 55 EGP
  • Available payment methods are
    Cash on Delivery
  • Delivery fees are 0-25 EGP, with delivery expected within 1-3 day(s)
  • Similar products to A4988 Stepper Motor Driver (2A) are sold at TechDepot Egypt, RAM Electronics, Future Electronics with prices starting at 40 EGP
  • The first appearance of this product was on Jan 29, 2016
  • Amongst similar products of A4988 Stepper Motor Driver (2A) the cheapest price is 40 EGP from TechDepot Egypt

Future Electronics's Description

Stepper motor driver Allegro’s A4988 DMOS Micro-stepping Driver with adjustable current limiting, overcurrent and overtemperature protection, and five different microstep resolutions (down to 1/16-step).

The driver requires a logic supply voltage (3 – 5.5 V) and a motor supply voltage (8 – 35 )V. It can deliver up to approximately 1 A per phase without a heat sink or forced air flow (it is rated for 2 A per coil with sufficient additional cooling).

This A4988 stepper driver is provided with heat sink to protect the board from overheating.

Features

  • Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step
  • Adjustable current control lets you set the maximum current output with a potentiometer.
  • Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection
  • Short-to-ground and shorted-load protection

The driver requires a logic supply voltage (3 – 5.5 V) to be connected across the VDD and GND pins and a motor supply voltage (8 – 35 V) to be connected across VMOT and GND. The logic voltage can be supplied from an external source, such as that powering the logic of the rest of the system.

The resolution (step size) selector inputs (MS1, MS2, MS3) enable selection from the five step resolutions according to the table below.

Control inputs

Each pulse to the STEP input corresponds to one microstep of the stepper motor in the direction selected by the DIR pin. Note that the STEP and DIR pins are not pulled to any particular voltage internally, so you should not leave either of these pins floating in your application. If you just want rotation in a single direction, you can tie DIR directly to VCC or GND. For details about these power states, see the datasheet.

Current Limiting

 One way to set the current limit is to put the driver into full-step mode and to measure the current running through a single motor coil without clocking the STEP input. The measured current will be 0.7 times the current limit (since both coils are always on and limited to 70% of the current limit setting in full-step mode).

Allegro’s A4988 DMOS Mmcro-stepping driver IC datasheet

Reviews of A4988 Stepper Motor Driver (2A)

  • No reviews exist yet for this product.

Similar Products

ProductStorePricePayment methodsDelivery timeFees

Store: TechDepot Egypt

Price: 40 EGPPayment methods:
Cash on Delivery
Delivery time: 5+ day(s) Fees : 35-45 EGP Buy it

Store: RAM Electronics

Price: 140 EGPPayment methods:
Cash on Delivery
Delivery time: N/A Fees : N/A Buy it

Store: Future Electronics

Price: 170 EGPPayment methods:
Cash on Delivery
Delivery time: 1-3 day(s) Fees : 0-25 EGP Buy it

Store: TechDepot Egypt

Price: 190 EGPPayment methods:
Cash on Delivery
Delivery time: 5+ day(s) Fees : 35-45 EGP Buy it

Store: RAM Electronics

Price: 1,650 EGPPayment methods:
Cash on Delivery
Delivery time: N/A Fees : N/A Buy it